Universal Remote Control Universal Remote UR5 8400 User Manual

STEP1 Press the [CBL] button and the  
[SELECT] button simultaneously  
for 3 seconds.  
STEP3 Press the [DEVICE] button and the  
[POWER] button you wish to store in  
the [SYSTEM ON/OFF] button and  
repeat this until you stored all the  
power commands into the [SYSTEM  
ON/OFF] button.  
STEP4 Press the [CH+] button to save the  
power commands you stored. The  
[CBL] button will blink twice to  
confirm the saving.  
C. To Find the Three Digit Code Number  
That was Stored in the Device.  
STEP1 Press the [DEVICE] button (TV, VCR ,  
DVD or AUX) you wish to verify and  
the [SELECT] button simultaneously  
for 3 seconds. The device LED will  
turn on.  
*Tip : The equipment will turn off when the  
correct three-digit code number has  
been entered. You can verify you have  
selected the correct code by pressing  
the [POWER] button, the equipment  
should turn on or turn off.  
Introduction  
Button Functions  
3
1
Operating Instructions  
For The UR5-8400  
The remote control is designed to operate  
the Scientific Atlanta Explorer 8000, Pioneer  
Voyager DVR and the Pace Micro DVR  
Series. You can also control the majority of  
TV, VCR, DVD and AUDIO equipment on the  
market as shown below.  
The [CBL] device LED will turn on.  
*Tip :The device LED will turn on for 20  
seconds. The next step must be  
entered while the LED is on.  
Cable Remote Control  
*Note : If there is more than one three-digit  
number listed for your brand, try one  
code number at a time until your  
equipment turns off.  
STEP2 Press the [VOL +] button.  
*Tip : The device LED will turn on for 20  
seconds. The next step must be  
entered while the LED is on.  
CABLE : Cable Converters  
VCR : VCRs and TV/VCRs  
AUX : Audio Receivers, etc.  
TV : Televisions  
UR5-8400  
DVD : DVD Players  
STEP3 Press the [CBL] button.  
The device LED will blink twice to  
confirm the programming.  
STEP4 Store the three-digit code number  
by pressing the same [DEVICE]  
button once again. The device LED  
will blink twice to confirm that the  
code has been stored.  
F. Programming Channel Control.  
STEP2 Press the [INFO] button.  
Replacing Batteries  
2
To return to original state:  
By following the steps below, the user can  
program the channel controls (Channel Up,  
Channel Down and Last) from one device to  
operate in another device mode. The default  
channel control settings on the remote  
control are as follows:  
The device LED will blink number of times  
indicating the number of each digit of the  
code number. Each digit is separated by a 1  
second interval of the LED being turned off.  
If you wish to restore the TV volume  
control in CBL mode, repeat the above  
Before you program or operate the remote control,  
you must install two new AA alkaline batteries.  
steps by pressing [TV] in STEP3  
.
STEP1 Remove the battery compartment cover  
*Note : Try all the functions on the remote  
control. If any of the functions do not  
work as they should, repeat from  
Step 2 using the next three-digit code  
number from the same brand list.  
on the back of your remote control.  
Example : One blink, three blinks and eight  
blinks with an interval of 1 second  
of LED being turned off, indicates  
the code number 138.  
STEP2 Check battery polarity carefully, and  
install the batteries as shown In the  
illustration below.  
H. Programming For Advanced Function.  
CBL : CBL  
VCR : CBL  
AUX : AUX  
T V : CBL  
DVD : DVD  
In the CBL mode, the BLANK button can be  
programmed to act as a macro or favorite  
channel button. You can send out up to ten  
commands with one button press.  
STEP3 Replace the battery compartment cover.  
Note : Ten blinks is equal to the number 0.  
If you wish to store the TV channel control in  
TV mode, use the following steps.  
B. Auto Search Method.  
D. Programming a second TV to AUX Mode.  
STEP1 Press the [CBL] button to select  
If the three-digit code numbers assigned to  
your brand do not turn off your equipment or  
the code tables do not list your brand, you  
can use the Auto Search Method to find the  
correct three-digit code number for your  
equipment by the following steps:  
the CBL mode.  
STEP1 Press the [AUX] button to be  
programmed and the [SELECT] button  
simultaneously for 3 seconds.The  
[AUX] device LED will turn on.  
STEP1 Press the [TV] button and the  
[SELECT] button simultaneously for  
3 seconds.  
STEP2 Press the BLANK button and  
[SELECT] button simultaneously  
for 3 seconds. The [CBL] device  
LED will turn on for 20 seconds.  
STEP3 Press up to 10 buttons you wish to  
store. The [CBL] device LED will blink  
once for each command entered.  
STEP4 Press the [CH+] button to store the  
functions that were selected. The  
[CBL] device LED will blink twice to  
confirm the storage of functions.  
The [TV] device LED will turn on.  
*Tip : The device LED will turn on for 20  
seconds. The next step must be  
entered while the LED is on.  
*Tip :The device LED will light on for 20  
seconds. The next step must be  
entered while the LED is on.  
STEP1 Turn on the equipment you wish to  
operate.  
STEP2 Press the [TV] device button to pick  
STEP2 Press the [VOL -] button.  
STEP2 Press the [DEVICE] button (TV, VCR,  
DVD or AUX) to be programmed and  
the [SELECT] button simultaneously  
for 3 seconds. The device LED will  
turn on.  
up the TV code table.  
STEP3 Press the [TV] button.  
The device LED will blink twice to  
confirm the programming.  
STEP3 Point the remote control toward the  
equipment and enter the three-digit  
code number assigned to your TV  
brand from the code tables.  
STEP4 Store the three-digit code number by  
pressing the [AUX] button once  
again. The device LED will blink  
twice to confirm that the code has  
been stored.  
I. Low Battery Warning.  
To return to original state:  
When the batteries are low and need to be  
replaced with fresh batteries, the remote  
control LED will blink 2 times in sequence  
whenever a [POWER] button is pressed to  
turn on equipment.  
If you wish to restore the CABLE channel  
*Tip : The device LED will turn on for 20  
seconds. The next step must be  
entered while LED is on.  
Operations  
4
control in TV mode, repeat the above steps  
Programming the Remote Control  
5
by pressing [CBL] in STEP3  
.
Default State:  
Device Default: CABLE  
STEP3 Press the [CH+] or [CH-] button one  
at a time or keep it pressed. The  
remote will emit a series of power  
on/off commands. Release the  
[CH+] or [CH-] button as soon as the  
equipment turns off.  
*Tip : You can verify that you selected the  
correct code by pressing the [POWER]  
button. The equipment should either  
turn on or turn off.  
A. Three-Digit Code Programming Method.  
The remote control can be programmed by pressing in a three-digit code number that  
corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit  
code numbers are listed in the code table of the instruction manual.  
Volume Default: You have the option of controlling  
your TV volume and mute through the Cable box,  
VCR or DVD. Refer to section G for programming the  
volume and mute through your Cable box, VCR or  
DVD.  
G. Programming Volume Control.  
J. Memory Lock System.  
By following the steps below, the user can  
program the volume controls (Volume Up,  
Volume Down and Mute) from one device to  
operate in another device mode. The default  
volume control settings on the remote  
control are as follows:  
This remote control is designed to retain  
programmed memory for 10 years even  
after batteries are removed from the  
remote control.  
E. Programming the System On/Off Button.  
This is designed to program the System On/Off  
button so that it can send out up to five power  
on/off commands with one button press.  
STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX)  
Channel Default: You have the option of controlling  
your CABLE channel and number keys through the  
TV or VCR. Refer to section F for programming the  
channel and number keys through your TV or VCR.  
STEP2 Press the [DEVICE] button (TV, VCR, DVD or AUX) to be programmed and [SELECT]  
button simultaneously for 3 seconds. The device LED will turn on indicating the unit is  
ready to be programmed.  
K.Write your device Set-up codes.  
STEP1 Press the [CBL] button.  
TV  
Set-up Code Number:  
CBL : TV  
VCR : TV  
AUX : AUX  
T V : TV  
DVD : TV  
STEP2 Press the [SYSTEM ON/OFF] button  
and the [SELECT] button  
System On/Off button:  
VCR Set-up Code Number:  
DVD Set-up Code Number:  
AUX Set-up Code Number:  
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED  
This button is designed to send out power  
commands for two, three, four or all five devices with  
one button press. Please refer to section E for  
details.  
Universal Remote Control, Inc.  
STEP4 Press the same [DEVICE] button to  
store the code. The device LED will  
blink twice to confirm that the code  
has been stored.  
is on.  
simultaneously for 3 seconds. The  
[CBL] button will turn on for 20  
seconds.  
STEP3 Point the remote control toward the equipment and enter the three-digit code number  
OCE-0017D Rev 03 (11/29/05)  
If you wish to store the CBL volume control in  
CBL mode, use the following steps.  
assigned to your brand from the code tables.  
 

Timex Fitness Electronics 620 095000 User Manual
Toshiba All in One Printer Studio 352 User Manual
Transcend Information Computer Drive StoreJet 25 Version 13 User Manual
Tricity Bendix Cooktop CSIE 506 X User Manual
Tyco Electronics Portable Radio M7300 Series User Manual
Uniden Two Way Radio GMR1048 2CK User Manual
Viking Gas Grill VGBQ3002T1NSS User Manual
Vizio Computer Accessories CCU 11B User Manual
Vizio Flat Panel Television D32h C1 User Manual
VTech Cordless Telephone i 5836 User Manual