Vermont Casting Indoor Fireplace DEF User Manual

INSTALLER/CONSUMER  
SAFETY INFORMATION  
PLEASE READ THIS MANUAL  
BEFORE INSTALLING AND  
USING APPLIANCE.  
Electric  
Fireplace  
Model: DEF/DEFD26  
WARNING!  
IF THE INFORMATION IN THIS  
MANUAL IS NOT FOLLOWED  
EXACTLY, AN ELECTRICAL  
SHOCK OR FIRE MAY RESULT  
CAUSING PROPERTY DAMAGE,  
PERSONAL INJURY OR LOSS  
OF LIFE.  
FOR YOUR SAFETY  
Service must be performed by  
a qualified service agency.  
DO NOT STORE OR USE  
GASOLINE OR OTHER  
FLAMMABLE VAPORS AND  
LIQUIDS IN THE VICINITY OF  
THIS OR ANY OTHER  
APPLIANCE.  
DEF26_photo  
Homeowner’s Installation &  
Operating Manual  
C
US  
Verm on t Castin gs, Majestic Products  
410 Admiral Blvd. Mississauga Ontario, Canada L5T 2N6 Ph: 905-670-7777  
INSTALLER: DO NOT DISCARD THIS MANUAL - LEAVE FOR HOMEOWNER  
10005581 07/03 Rev.0  
 
Installation Instructions  
fireplace should not be used as a drying rack for  
clothing, nor should Christmas stockings or  
decorations be hung in the area of it.  
General  
1. Read all instructions before using this appliance.  
16. Use this appliance only as described in this  
manual. Any other use not recommended by the  
manufacturer may cause fire, electric shock or  
injury to persons.  
2. This appliance is hot when in use. To avoid burns,  
do not let bare skin touch hot surfaces. If provided,  
use handles when moving this appliance. Keep  
combustible materials, such as furniture, pillows,  
bedding, papers, clothes and curtains at least 3'  
(1 m) from the front of this appliance.  
17. Avoid the use of an extension cord because the  
extension cord may overheat and cause a risk of  
fire. However, if you have to use an extension  
cord, the cord shall be No. 14 AWG minimum size  
and rated not less than 1875 Watts. The extension  
cord must be a 3-wire cord with grounding-type  
plug and cord connection. The extension cord  
shall not be more than 20' (6.1 m) in length.  
CAUTION: Extreme caution is necessary  
when any heater is used by or near  
children or invalids and whenever the  
heater is left operating and unattended.  
3. If possible, always unplug this appliance when not  
in use.  
18. SAVE THESE INSTRUCTIONS.  
4. Do not operate any heater with a damaged cord or  
plug or after the appliance malfunctions, or if it has  
been dropped or damaged in any manner.  
Locating Your  
5. Any repairs to this fireplace should be carried out  
by a qualified service person.  
Electric Fireplace  
Your new fireplace may be installed with an approved  
Vissan cabinet.  
6. Under no circumstances should this fireplace be  
modified. Parts having to be removed for servicing  
must be replaced prior to operating this fireplace  
again.  
When choosing a location for your new fireplace,  
ensure that the general instructions are followed. For  
best effect, install the fireplace out of direct sunlight.  
7. Do not use outdoors.  
8. This heater is not intended for use in bathrooms,  
laundry areas and similar indoor locations. Never  
locate this appliance where it may fall into a bath-  
tub or other water container.  
Clearance to Combustibles  
Sides .................................. 0" (0 mm)  
Floor ................................... 0" (0 mm)  
Top ..................................... 0" (0 mm)  
9. Do not run cord under carpeting. Do not cover cord  
with throw rugs, runners or the like. Arrange cord  
away from traffic areas and where it will not be  
tripped over.  
Hearth  
10. To disconnect this appliance, turn controls to the  
A hearth is not mandatory; however, it is recommended  
for aesthetic purposes. Installation of a noncombustible  
hearth that will not obstruct the louvre opening is  
recommended.  
OFF position, then remove plug from outlet.  
11. Connect to properly grounded outlets only.  
12. This appliance, when installed must be electrically  
grounded in accordance with local codes or, in the  
absence of local codes, with the current CSA  
C22.1 Canadian Electrical Code or for U.S.A.  
installations follow local codes and the National  
Electrical Code, ANSI/NFPA NO. 70.  
Cold climate installation recommendation:  
When installing this unit against a non-  
insulated exterior wall or chase, it is  
mandatory the outer walls be insulated to  
conform to applicable insulation codes.  
13. Do not insert or allow foreign objects to enter any  
ventilation or exhaust opening as this may cause  
an electric shock or fire, or damage the appliance.  
Electrical Specifications  
14. To prevent a possible fire, do not block air intakes  
or exhaust in any manner. Do not use on soft  
surfaces, like a bed, where openings may become  
blocked.  
Voltage:  
120VAC, 60Hz  
12.2 Amps  
Total Amps:  
Total Watts:  
1460 Watts  
Heater Rating: 1300 Watts  
15. This appliance has hot and arcing or sparking parts  
inside. Do not use it in areas where gasoline, paint  
or flammable liquids are used or stored. This  
10005581  
3
 
Verm ont Castings, Majestic Products DEF/ DEFD26  
Optional Cabinet Dimensions  
C
E
Face  
Pillar  
A
Front and Side  
Views of Cabinet  
D
B
G
F
Back edge  
5581 cab dims  
J
K
I
H
Front Base  
5581 base dims  
Reference  
All Models  
A
B
C
D
E
F
G
H
I
26 5/8" (676 mm)  
26 1/2" (673 mm)  
43 7/8" (1114 mm)  
36 1/2" (927 mm)  
13" (330 mm)  
10 3/8" (264 mm)  
38 1/2" (978 mm)  
44 1/4" (1124 mm)  
3" (76 mm)  
45 1/4" (1149 mm)  
15 1/2" (394 mm)  
J
K
Optional Cabinet Installation  
1. Refer to the installation instructions on Page 3 in  
this owner's manual for electrical hookup and  
SAFETY RULES.  
4. Place the cabinet assembly over the fireplace. The  
opening in cabinet fits over fireplace, back edges of  
the cabinet flush against the wall. Place the front of  
the fireplace up flush against the front face of the  
cabinet between the two (2) pillars.  
2. Place the cabinet base into position, back edges of  
the cabinet base flush against the wall.  
3. Place the fireplace onto the base, centered side-to-  
side, back edge of fireplace approximately 1"  
(25 mm) out from the wall.  
4
10005581  
 
Verm ont Castings, Majestic Products DEF/ DEFD26  
Fireplace Dimensions  
ROD  
ROH  
ROW  
A
Framing & Finishing  
B
C
G
E
F
A
D
5581 HEF26 specs  
Reference  
All Models  
A
B
C
D
E
F
26 1/8" (664 mm)  
25 7/8" (657 mm)  
17 1/2" (445 mm)  
24 1/4" (615 mm)  
10" (254 mm)  
20 1/8" (511 mm)  
21 1/4" (540 mm)  
G
Rough Opening Depth (ROD)  
Rough Opening Width (ROW)  
Rough Opening Height (ROH)  
10 1/2" (267 mm)  
26 5/8" (676 mm)  
26 3/8" (670 mm)  
10005581  
5
 
Verm ont Castings, Majestic Products DEF/ DEFD26  
WARNING: Electrical outlet wiring must  
comply with local building codes and  
other applicable regulations to reduce  
the risk of fire, electrical shock and  
injury to persons.  
Screen Information  
1. Under no circumstances is this product to be  
operated if the screen door(s) are missing.  
2. Do not strike or slam the screen doors.  
WARNING: Do not use this fireplace if  
any part of it has been under water.  
Immediately contact a qualified service  
technician to inspect the fireplace and  
replace any part of the electrical system.  
3. This product uses screen doors. Replacement  
screen doors are available from the manufacturer.  
Replacement must be carried out by a qualified  
service person.  
Electrical Connection  
WARNING: This fireplace comes with a  
manual circuit breaker reset near the  
power cord supply. In case the fireplace  
is not operating check the circuit breaker  
and reset the button at the breaker. If the  
fireplace remains inoperable,  
A 15 AMP, 120 Volt, 60 Hz circuit with a properly  
grounded outlet is required. Preferably, the fireplace  
will be on a dedicated circuit as other appliances on  
the same circuit may cause the circuit breaker to trip or  
the fuse to blow when the heater is in operation.  
immediately contact a qualified service  
technician to perform an inspection.  
The unit comes standard with a 6’ (1828 mm) long  
3-wire cord, exiting from the side of the fireplace.  
Plan the installation to avoid the use of an extension  
cord. If an extension cord must be used, it must be a  
minimum 14 AWG, 3-wire cord with grounding-type  
plug connector, and rated not less than 1875 Watts.  
The cord shall not be more than 20' (6.1 m) in length.  
Service Instructions  
Cleaning Trim  
Removal of Logs  
Clean the metal trim using a soft cloth, slightly  
dampened with lemon oil, then buff with a clean soft  
cloth. DO NOT use brass polish or household  
cleaners, as these products will damage the metal  
trim. Lemon oil may be obtained at supermarkets and  
hardware stores.  
1. Turn OFF power to the unit by unplugging the  
power cord.  
2. Let fireplace cool if it has been operating.  
3. Gently open both screen doors.  
4. Remove the two (2) screws securing the ember bed  
and logset in position. One (1) screw is located on  
either side of the ember bed near the center.  
LG237_DEF26_logs  
Fig. 1 Electric logset  
WARNING: Disconnect power before  
attempting any maintenance or cleaning  
to reduce the risk of fire, electrical shock  
or personal injury.  
6
10005581  
 
Verm ont Castings, Majestic Products DEF/ DEFD26  
Replacing the Light Bulbs  
Trim Kit Installation  
This fireplace uses two (2) clear 120 Volt, 60 Watt,  
E-12 socket base light bulbs (small base, chandelier  
candle type). The 60 Watt bulbs are located under the  
logset/ember bed. For convenience, if one (1) of the  
bulbs burns out, it will be prudent to replace both of the  
light bulbs.  
1. Peel all plastic from the Trim Kit Assembly.  
2. Press the Trim Kit Assembly onto the front of the  
fireplace. To facilitate the installation process, these  
pieces are magnetized. Align the top of the Trim Kit  
Assembly with the top of the fireplace.  
1. Turn OFF power to the unit by unplugging the power  
cord.  
2. Let fireplace cool if it has been operating.  
3. Remove the four (4) screws securing the bottom  
louvre. Pull the louvre up and lift it out.  
4. Examine the bulbs to determine which bulb needs to  
be replaced.  
5. While holding the socket, unscrew defective bulb(s).  
6. Install the new light bulb(s) by screwing it in while  
holding the socket.  
7. Reinstall the bottom louvre. Follow the above  
procedure in reverse order.  
WARNING: Do not exceed 60 Watts per  
bulb. Use of higher-rated bulbs may result  
in a fire, causing property damage or  
personal injury.  
DEF26_3D  
Fig. 2 Trim kit installation  
Maintenance of Motors  
The motors used on the fan and the flame generator  
assembly are prelubricated for extended bearing life  
and require no further lubrication. However, periodic  
cleaning/vacuuming of the fan/heater unit is  
recommended.  
WARNING: Make sure the power is  
turned OFF before proceeding.  
10005581  
7
 
Verm ont Castings, Majestic Products DEF/ DEFD26  
Electrical Wiring Diagram with Integral Remote Control  
If repairing or replacing any electrical  
component or wiring, the original wire  
routing, color coding and securing  
locations must be followed.  
Any electrical repairs or rewiring of this unit should be  
carried out by a licensed electrician in accordance with  
national and local codes.  
1. Motor Variable Speed 12VDC  
2. Switch ON/OFF  
5
1
3. Thermostat  
4. Fan/Heater  
BLACK  
WHITE  
BLACK  
FLAME  
RED MOTOR  
5. Light Socket w/Wiring Assemblyy  
6. Light Bulb 60 W  
10  
10  
7. Breaker Circuit Manual Reset  
8. Power Cord 16/3 HPN with Terminal  
9. Bushing Straight-Thru Strain Relief  
10  
6
FAN  
MOTOR  
1
4
10. Cable Tie Nylon 6" - 1 /8 Black  
14  
11  
11. Bushing Snap 0.875"-0.625"  
12. CFM Majestic Factory Wire Required  
13. Receiver  
13 WHITE  
+
SPEED  
CONTROL  
-
HEATER  
ELEMENT  
6 BLACK  
7
14. Potentiometer with Harness Assembly  
11  
12 WHITE  
10  
8 RED  
9
8
3 BLACK  
2
BREAKER  
CIRCUIT  
1 BLACK  
5 BLACK  
15 WHITE  
T'  
S
T
A
T
SWITCH  
ON/OFF  
IN  
N
N
L
L
OUT  
IN  
3
4 BLACK  
13  
OUT  
10005352  
Electrical Wiring Diagram without Integral Remote Control  
BLACK  
FLAME  
BLACK  
MOTOR  
1. 120VAC Motor  
2. Rocker Switch  
5
1
3. Thermostat  
4. Fan/Heater  
BLACK  
WHITE  
5. Light Socket with Wiring  
Assembly (2 Lamps)  
6. Light Bulb 60 W  
7. Breaker Circuit Manual Reset  
8. Power Cord  
10  
10  
6
FAN  
MOTOR  
9. Bushing Strain Relief  
4
1
10. Nylon Cable Tie 6 /8 Black  
11. Bushing Snap Hole  
11  
12. CFM Majestic Factory Wire  
HEATER ELEMENT  
6 RED  
7
9 WHITE  
8 WHITE  
10  
BREAKER  
CIRCUIT  
9
8
2 BLACK  
1 BLACK  
3 BLACK  
2
7 WHITE  
THERMOSTAT  
SWITCH ON/OFF  
3
10005350  
8
10005581  
 
Verm ont Castings, Majestic Products DEF/ DEFD26  
Operating Instructions  
NOTE: The control compartment is located behind the upper louvre panel. To access controls, flip the upper  
louvre panel down.  
4. Re-learn  
3
2
1
5
4
This model fireplace with integral remote control has a  
preprogrammed, matched-pair Receiver/Transmitter  
already set with randomly-selected house codes. It is  
highly unlikely that the fireplace code will ever need to  
be re-learned. If the fireplace needs to re-learn  
Receiver/Transmitter house codes, perform the  
following steps:  
10005754  
1. Be sure there is power to the fireplace.  
Fig. 3 Control locations behind upper louvre panel.  
2. Be sure there is a good battery in the Transmitter  
(hand-held remote).  
1. Main ON/OFF Switch  
3. Open the battery compartment of the remote.  
The ON/OFF switch supplies power to all functions of  
the fireplace. This is an illuminated switch which  
normally lights up when in the ON or OFF position.  
4. Press and release the small button located in the  
top left corner. This will randomly select a new  
house code in the remote Transmitter.  
5. Close the remote Transmitter battery  
compartment.  
2. Heater Control  
6. Press either the ON or OFF button on the remote  
Transmitter, and the Learn button on the fireplace  
at the same time. The fireplace is now ready to  
accept commands from the remote Transmitter.  
The Heater Control acts to turn the heater ON and  
OFF as well as setting the comfort level in the room.  
Turning the knob clockwise from the OFF position will  
place the heater into operation. The further the knob is  
rotated clockwise, the higher the setpoint temperature.  
Turning the knob counterclockwise will lower the  
setpoint temperature. Turning it all the way  
5. ON/OFF  
The ON/OFF button on the fireplace (below the Learn  
button) is to turn the fireplace ON and OFF when the  
battery in remote Transmitter is weak, or to manually  
operate the fireplace without the remote Transmitter.  
counterclockwise will turn the heater function OFF.  
WARNING: During any service of this  
appliance, the power to the unit must be  
turned OFF. It is not acceptable to use the  
ON/OFF switch to meet this requirement.  
NOTE: The device complies with Part 15 of the  
FCC Rules. Operation is subject to the  
following two conditions:  
3. Flame Speed Control  
1. This device may not cause harmful  
interference, and  
Turn the flame speed control knob to increase or  
decrease the flame speed as desired.  
2. This device must accept any  
interference received, including  
interference that may cause  
undesired operation.  
10005581  
9
 
Verm ont Castings, Majestic Products DEF/ DEFD26  
Replacement Parts List  
Item #  
Part Description  
DEF26  
DEFD26  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
Log Set Complete  
Fan/Heater  
Flame Generator Motor, 120 Volt AC w/Terminal  
Cord Power 16/3 HPN w/Terminals  
ON/OFF Switch  
10004588  
10004198  
10004262  
10003095  
10001393  
10004199  
10001639  
10003093  
10003350  
10005345  
10003568  
10005135  
10005153  
10005330  
10005329  
10004588  
10004198  
10003095  
10001393  
10004199  
10001639  
10003093  
10003350  
10005345  
10003568  
10005135  
10005153  
10005330  
10005329  
10001978  
10001168  
10001589  
10005140  
10005141  
10005758  
Heater Control (Thermostat)  
Heater Control Knob  
Breaker Circuit Manual Reset  
Flame Generator Assembly  
Screen Light Tinted (not shown)  
Light Bulb Socket w/Wiring Assembly  
Top Louvre Assembly  
Bottom Louvre Assembly  
Frame Door Screen Left Assembly  
Frame Door Screen Right Assembly  
Motor 12 VDC Flame Generator  
Potentiometer w/Harness Assembly  
Circuit Board Flame Speed Control  
Transmitter  
Receiver  
CFM-Majestic Wire (not shown)  
10005347  
2
11  
1
17  
4
3
20  
6
5
7
8
16  
12  
14  
19  
6
15  
13  
9
5581_DEF26_parts  
Vermont Castings, Majestic Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and  
products at any time, without notice.  
10  
10005581  
 
1 YEAR WARRANTY  
For Verm on t Castin gs, Majestic Products Electric Fireplace Models  
BASIC WARRANTY:  
GARANTIE DE BASE:  
Vermont Castings, Majestic Products (hereinafter referred to  
collectively as the "Company") warrants that your new  
Vermont Castings, Majestic Products fireplace is free from  
manufacturing and material defects for a period of one (1) year  
from date of installation, subject to the following conditions  
and limitations:  
Vermont Castings, Majestic Products (aux présentes nommée  
la "Société") garantit votre nouveau foyer électrique Vermont  
Castings, Majestic Products contre tous défauts de fabrication  
et de matières premières pour une période d'un an à compter  
de la date d'installation, sujet aux conditions et limitations  
suivantes.  
1. Le foyer électrique doit être installé par un entrepreneur de  
service autorisé et compétent. Il doit être installé et utilisé en tout  
temps selon les instructions d'installation et de fonctionnement  
fournies avec le produit. Toute altération, abus volontaire,  
accident ou mauvais usage du produit annulera cette  
garantie.  
2. Cette garantie n'est pas transférable et est offerte à l'acheteur au  
détail d'origine, à condition que l'achat soit effectué par l'entre-  
mise d'un détaillant autorisé de la Société.  
3. Cette garantie est limitée à la réparation ou au remplacement  
de(des) pièce(s) trouvée(s) défectueuse(s) en matières premiè-  
res ou main-d'oeuvre, à condition que lesdites pièces aient été  
sujettes aux conditions normales d'usage et de service, après  
que ledit défaut a été confirmé par une inspection par la Société.  
4. Cette Garantie ne couvre pas les ampoules inclus dans le  
foyer électrique Vermont Castings, Majestic Products.  
5. La Société peut, à sa discrétion, se décharger entièrement de  
toutes obligations se rapportant à cette garantie en remboursant  
le prix de gros de la(des) pièce(s) défectueuse(s).  
6. Tous les frais/dépenses d'installation, de main-d'oeuvre, de  
construction, de transport ou autres causés par une (des)  
pièce(s) défectueuse(s), une réparation, un remplacement ou  
autre, ne seront pas couverts sous cette garantie, et la Société  
n'assume aucune responsabilité pour ceux-ci. De plus, la  
Société ne pourra être tenue responsable pour tous dommages  
fortuits ou indirects sauf la ou prévu par la loi.  
7. Toutes autres garanties, exprimées ou sous-entendues, en ce  
qui a trait au produit, ses composants et accessoires, ou toutes  
obligations/responsabilités de la part de la Société sont aux  
présentes expressément excluses.  
8. La Société ni n'assume, ni autorise aucun tiers assumer, en son  
nom, des autres dettes en ce qui concerne la vente de cette  
cheminée électrique.  
9. Les garanties, telles que décrites dans ce document, ne s'appli-  
quent accessoires non Vermont Castings, Majestic Products  
utilisés conjointement pour l'installation de ce produit.  
10. Cette garantie est nulle si:  
1. This electric fireplace must be installed and operated at all  
times in accordance with the Installation and Operating  
instructions furnished with the product. Any alteration, willful  
abuse, accident, or misuse of the product shall nullify this  
warranty.  
2. This warranty is nontransferable, and is made to the original  
owner, provided that the purchase was made through an  
authorized supplier of the Company.  
3. This warranty is limited to the repair or replacement of part(s)  
found to be defective in material or workmanship, provided that  
such part(s) have been subjected to normal conditions of use  
and service, after said defect is confirmed by the Company's  
inspection.  
4. This warranty does not cover the lightbulb(s) included with  
the Vermont Castings, Majestic Products electric fireplace.  
5. The Company may, at its discretion, fully discharge all  
obligations with respect to this warranty by refunding the  
wholesale price of the defective part(s).  
6. Any installation, labour, construction, transportation, or other  
related costs/expenses arising from defective part(s), repair,  
replacement, or otherwise of same, will not be covered by this  
warranty, nor shall the Company assume responsibility for  
same. Further, the Company will not be responsible for any  
incidental, indirect, or consequential damages, except as  
provided by law.  
7. All other warranties - expressed or implied - with respect to the  
product, its components and accessories, or any obligations/  
liabilities on the part of the Company are hereby expressly  
excluded.  
8. The Company neither assumes, nor authorizes any third party  
to assume, on its behalf, any other liabilities with respect to the  
sale of this electric fireplace.  
9. The warranties as outlined within this document do not apply to  
non-Vermont Castings, Majestic Products accessories used in  
conjunction with the installation of this product.  
This warranty is void if:  
a) The fireplace has been operated in atmospheres  
contaminated by chlorine, fluorine or other damaging  
chemicals.  
b) The fireplace is subjected to prolonged periods of  
dampness or condensation.  
a) Le foyer a été utilisé dans une atmosphère contaminée par  
du chlore, du fluor ou tous autres produits chimiques.  
b) Le foyer est assujetti à de longues périodes d'humidité ou  
de condensation.  
c) Toute altération, abus volontaire, accident ou mauvais  
usage du produit annulera cette garantie.  
c) Any alteration, willful abuse, accident, or misuse of the  
product.  
PORTES EN VERRE & PIÈCES PLAQUÉES LAITON . . .  
Les portes en verre ne sont pas garanties contre le bris causé par un  
mauvais usage ou un accident.  
Les pièces en laiton devraient être nettoyées qu'avec de l'essence  
de citron. Les nettoyeurs de laiton ne peuvent pas être utilisés. La  
Société ne sera pas responsable pour, et ne garantit pas les pièces  
en laiton qui sont endommagées par de refoulement.  
GLASS DOORS & BRASS PLATED PARTS . . .  
Glass doors are not warranted for breakage due to misuse or  
accident.  
Brass parts should be cleaned with lemon oil only. Brass cleaners  
cannot be used. Mortar mix and masonry cleaners may corrode  
the brass finish. The Company will not be responsible for, nor will it  
warrant any brass parts which are damaged by external chemicals.  
SI UN SERVICE SOUS GARANTIE EST REQUIS . . .  
IF WARRANTY SERVICE IS NEEDED . . .  
1) Communiquez avec votre détaillant. Assurez-vous que vous avez  
votre garantie, votre reçu de caisse ainsi que le numéro de modèle/  
série de votre produit Vermont Castings, Majestic Products.  
2) NE TENTEZ PAS D'EFFECTUER DES RÉPARATIONS VOUS-MÊME.  
1) Contact your supplier. Make sure you have your warranty, your  
sales receipt, and the model/serial number of your Vermont  
Castings, Majestic Products appliance.  
2) DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.  
Verm on t Castin gs, Majestic Products  
410 Admiral Blvd. Mississauga Ontario, Canada L5T 2N6 Ph: 905-670-7777  
 

Technika Flat Panel Television LCD 19 240 User Manual
The Speaker Company Portable Speaker IndooR oUtdooR SpEakERS User Manual
TRENDnet Network Card TEW 430APB User Manual
Tricity Bendix Oven BS 612 2 User Manual
Tripp Lite Network Cables N002 025 WH User Manual
Uniflame Charcoal Grill CBC1232SP User Manual
Universal Remote Control Universal Remote URC 4021 User Manual
Vantec Computer Accessories MRK401STBK User Manual
Vizio TV Antenna E500i B1 User Manual
Vulcan Hart Griddle 902A ML 52630 User Manual