Universal Remote Control Universal Remote UR4 EXP User Manual

STEP3 Press the [DEVICE] button and the  
[POWER] button you wish to store in  
the System On/Off button and repeat  
this until you stored all the power  
commands into the System On/Off  
button.  
STEP4 Press the [CH+] button to save the  
power commands you stored. The  
[CBL] button will blink twice to  
confirm the saving.  
STEP1 Press the [CBL] button and the  
[SELECT] button simultaneously  
for 3 seconds.  
C. To Find the Three Digit CodeNumber  
That was Stored in the Device.  
STEP1 Press the [DEVICE] button (TV, VCR  
or AUX) you wish to verify and the  
[SELECT] button simultaneously for 3  
seconds. The device LED will turn on.  
*Tip : The equipment will turn off when the  
correct three-digit code number has  
been entered. You can verify you have  
selected the correct code by pressing  
the [POWER] button, the equipment  
should turn on or turn off.  
Introduction  
Button Functions  
3
1
Operating Instructions  
For 4 in 1  
The remote control is designed to operate  
the Scientific-Atlanta Explorer series and  
The Pioneer Voyager set top boxes. You can  
also control the majority of TV, VCR/DVD and  
AUDIO equipment on the market as shown  
below.  
*Tip :The device LED will turn on for 20  
seconds. The next step must be  
entered while the LED is on.  
Cable Remote Control  
*Note : If there is more than one three-digit  
number listed for your brand, try one  
code number at a time until your  
equipment turns off.  
STEP2 Press the [VOL +] button.  
*Tip : The device LED will turn on for 20  
seconds. The next step must be  
entered while the LED is on.  
STEP3 Press the [CBL] button.  
The device LED will blink twice to  
confirm the programming.  
CABLE : Cable Converters  
UR4-EXP  
TV  
: Televisions  
VCR : VCRs and DVD  
AUX : Audio Receivers, DMX, DCR, TIVO, etc.  
STEP2 Press the [INFO] button.  
STEP4 Store the three-digit code number  
by pressing the same [DEVICE]  
button once again. The device LED  
will blink twice to confirm that the  
code has been stored.  
F. Programming Channel Control.  
To return to original state:  
The device LED will blink number of times  
indicating the number of each digit of the  
code number. Each digit is separated by a 1  
second interval of the LED being turned off.  
Replacing Batteries  
2
If you wish to restore the TV volume  
control in CBL mode, repeat the above  
By following the steps below, the user can  
program the channel controls (Channel Up,  
Channel Down and Last) from one device to  
operate in another device mode. The default  
channel control settings on the remote  
control is as follows:  
Before you program or operate the remote control,  
steps by pressing [TV] in STEP3  
.
you must install two new AA alkaline batteries.  
*Note : Try all the functions on the remote  
control. If any of the functions do not  
work as they should, repeat from  
Step 2 using the next three-digit code  
number from the same brand list.  
STEP1 Remove the battery compartment cover  
Example : One blink, three blinks and eight  
blinks with an interval of 1 second  
of LED being turned off, indicates  
the code number 138.  
H. Programming For Advanced Function.  
on the back of your remote control.  
In the CBL mode, the A, B and C buttons  
can be programmed to act as a macro or  
favorite channel button to send out up to 10  
commands with one button press.  
STEP2 Check battery polarity carefully, and  
install the batteries as shown In the  
illustration below.  
CBL : CBL  
T V : CBL  
VCR : VCR  
AUX : AUX  
*Note : Ten blinks is equal to the number 0.  
If you wish to store the TV channel control in  
TV mode, use the following steps.  
STEP1 Press the [CBL] button to select  
STEP3 Replace the battery compartment cover.  
B. Auto Search Method.  
the CBL mode.  
D. Programming a second TV to AUX Mode.  
If the three-digit code numbers assigned to  
your brand do not turn off your equipment or  
the code tables do not list your brand, you  
can use the Auto Search Method to find the  
correct three-digit code number for your  
equipment by the following steps:  
STEP1 Press the [TV] button and the  
[SELECT] button simultaneously for  
3 seconds.  
STEP2 Press the [A, B, or C] button and  
[SELECT] button simultaneously  
for 3 seconds. The [CBL] device  
LED will turn on for 20 seconds.  
STEP1 Press the [AUX] button to be  
programmed and the [SELECT] button  
simultaneously for 3 seconds.The  
[AUX] device LED will turn on.  
*Tip :The device LED will light on for 20  
seconds. The next step must be  
entered while the LED is on.  
STEP3 Press up to 10 buttons you wish to  
store. The [CBL] device LED will blink  
once for each command entered.  
*Tip : The device LED will turn on for 20  
seconds. The next step must be  
entered while the LED is on.  
STEP1 Turn on the equipment you wish to  
STEP2 Press the [VOL -] button.  
operate.  
STEP4 Press the [CH+] button to store the  
functions that were selected. The  
[CBL] device LED will blink twice to  
confirm the storage of functions.  
STEP3 Press the [TV] button.  
The device LED will blink twice to  
confirm the programming.  
STEP2 Press the [TV] device button to pick  
STEP2 Press the [DEVICE] button (TV, VCR  
or AUX) to be programmed and  
the [SELECT] button simultaneously  
for 3 seconds. The device LED will  
turn on.  
up the TV code table.  
STEP3 Point the remote control toward the  
equipment and enter the three-digit  
code number assigned to your TV  
brand from the code tables.  
STEP4 Store the three-digit code number by  
pressing the [AUX] button once  
again. The device LED will blink  
twice to confirm that the code has  
been stored.  
To return to original state:  
I. Low Battery Warning.  
If you wish to restore the CABLE channel  
Operations  
Default State:  
Device Default: CABLE  
4
control in TV mode, repeat the above steps  
When the batteries are low and need to be  
replaced with fresh batteries, the remote  
control LED will blink 2 times in sequence  
whenever a [POWER] button is pressed to  
turn on equipment.  
*Tip : The device LED will turn on for 20  
seconds. The next step must be  
entered while LED is on.  
by pressing [CBL] in STEP3  
.
Programming the Remote Control  
5
G. Programming Volume Control.  
Channel Default: CABLE channel and number  
keys through the CABLE, with the option of  
controlling channel and number keys through  
the TV or VCR. Refer to section F for  
programming the channel and number keys  
through your TV or VCR.  
Volume Default: CABLE volume and mute  
through the TV, with the option of controlling  
volume and mute through the Cable box or Audio.  
Refer to section G for programming the volume  
and mute through your Cable box or Audio.  
STEP3 Press the [CH+] or [CH-] button one  
step at a time or keep it pressed.  
The remote will emit a series of  
Power ON/OFF commands. Release  
the [CH+] or [CH-] button as soon as  
the equipment turns off.  
*Tip : You can verify that you selected the  
correct code by pressing the [POWER]  
button. The equipment should either  
turn on or off.  
A. Three-Digit Code Programming Method.  
The remote control can be programmed by pressing in a three-digit code number that  
corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit  
code numbers are listed in the code table of the instruction manual.  
By following the steps below, the user can  
program the volume controls (Volume Up,  
Volume Down and Mute) from one device to  
operate in another device mode. The default  
volume control settings on the remote  
control is as follows:  
J. Memory Lock System.  
This remote control is designed to retain  
programmed memory for 10 years even  
after batteries are removed from the  
remote control.  
E. Programming the System On/Off Button.  
This is designed to program the System On/Off  
button so that it can send out up to four power  
on/off commands with one button press.  
STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX)  
STEP2 Press the [DEVICE] button (TV, VCR or AUX) to be programmed and [SELECT] button  
simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready  
to be programmed.  
CBL : TV  
T V : TV  
STEP1 Press the [CBL] button.  
K. Write your device Set-up codes.  
VCR : TV  
AUX : AUX  
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED  
System On/Off button:  
TV  
Set-up Code Number:  
STEP2 Press the [SYSTEM] button and the  
[SELECT] button simultaneously for 3  
seconds. The [CBL] button will turn  
on for 20 seconds.  
Universal Remote Control, Inc.  
If you wish to store the CBL volume control in  
CBL mode, use the following steps.  
The [CBL] device LED will turn on.  
STEP4 Press the same [DEVICE] button to  
store the code. The device LED will  
blink twice to confirm that the code  
has been stored.  
This button is designed to send out power  
commands for two, three or all four devices  
with one button press. Please refer to section E  
for details.  
is on.  
OCE-0005A Rev 08 (02/06/07)  
VCR Set-up Code Number:  
AUX Set-up Code Number:  
STEP3 Point the remote control toward the equipment and enter the three-digit code number  
assigned to your brand from the code tables.  
 

Technika Clock Radio SP 129I User Manual
Tektronix Yard Vacuum TM506 User Manual
The Singing Machine Microphone SMM 106 User Manual
Tiffen Camera Accessories Camera Bag User Manual
TOA Electronics Stereo Amplifier IWSA500 D User Manual
Tricity Bendix Cooktop SE554 User Manual
Ultra Products Ventilation Hood ULT30240 User Manual
Vienna Acoustics Speaker Klimt Series User Manual
Viking Outdoor Storage viking User Manual
Vizio Model Vehicle E552VLE User Manual